Hobie Mirage Drive Fin Upgrades for Kayak Fishing
 

Hobie Mirage Drive Fin Upgrades for Kayak Fishing



http://img.photobucket.com/albums/v2...sidebyside.jpg

Hobie’s innovative Mirage Drive has revolutionized the world of Kayak Fishing. No other kayak allows you ‘hands free’ capability. With Hobie, you have the free to fish while underway. Not only that, but its more efficient and much faster than a traditional kayak. Now, Hobie has improved upon its original Mirage Drive fin design with 2 new upgraded fins, the ST Fin and the ST Turbo Fin.

http://img.photobucket.com/albums/v2...ll/layered.jpg

The Standard or stock fin that comes with the Hobie Mirage Drive is 11 inches long with a curved bottom. The fin is very flexible providing for easy pedal strokes. This fin was designed for all skill levels, from the first timer to the seasoned salt.

The ST or “Square Tip” Fin is also 11 inches long, but instead of a curved bottom, it has a flat squared bottom. The fin is a bit stiffer than the standard fin and includes a tension screw that allows the user to increase or decrease the stiffness of the fin. This upgrade retails for $22.95 per fin or $45.90 for the pair.

The ST Turbo Fin is a beefed up version of the ST Fin. At 13.5 inches, it’s a full 2 and a half inches longer than the ST Fin. This additional length can provide for a 10% increase in speed (according to Hobie’s marketing material) You can also obtain top speed much more quickly and cruising speed is a breeze. This upgrade retails for $79.95 for the pair.



I’ve upgraded my Mirage Drive to the ST Turbo Fins for Kayak Fishing. I like the ability to chase down bird schools or just get out to the fishing grounds faster. Add a high performance sailing rudder and you’ve got a fishing machine.

Installation of the ST and ST Turbo Fins takes about 5 minutes and all required tools come with the upgrade kit.

ST Fin

First, you’ll need to remove the pin holding the rear of the fin.

http://img.photobucket.com/albums/v2...litringpin.jpg
http://img.photobucket.com/albums/v2...pinremoved.jpg

Then, slide the fin off of the mast

http://img.photobucket.com/albums/v2...xposedmast.jpg
http://img.photobucket.com/albums/v2...astremoval.jpg


Next, grab the ST Fin and slide it onto the mast.

http://img.photobucket.com/albums/v2...ingSTFinon.jpg


Finally, replace the pin on the rear of the fin.

http://img.photobucket.com/albums/v2...ll/pininST.jpg


ST Turbo Fin
The ST Turbo fins have an additional step, due to the longer mast (13.5 inches)

After you have removed the standard fin, you’ll need to replace the mast
First, loosen the set screw holding the mast

http://img.photobucket.com/albums/v2...l/setscrew.jpg
http://img.photobucket.com/albums/v2...valandtool.jpg



Then, slide the old mast out and insert the longer mast. Be careful to line up the notch in the mast with the set screw.

http://img.photobucket.com/albums/v2...wturbomast.jpg

Next, slide the ST Turbo fin onto the mast.

http://img.photobucket.com/albums/v2...oinstalled.jpg

Finally, replace the pin on the rear of the fin.

http://img.photobucket.com/albums/v2...ll/pininST.jpg

Got Any Questions, wanna order this product - Call Nate - the Hobie Guru @ 760-721-6195

Re: Hobie Mirage Drive Fin Upgrades for Kayak Fishing
 

FYI there is no set screw on the 2009 masts, they are using loctite to keep it in place........carry on peddlers.

Re: Hobie Mirage Drive Fin Upgrades for Kayak Fishing
 

Installed the Turbo fins. Tightened the screws on the rear of the fins fully. What's your opinion on the use of the screws? I could experiment while on the water, but would like your opinion.

I'm new to the forum. Disappointed that there is not more exchange?

Re: Hobie Mirage Drive Fin Upgrades for Kayak Fishing
 

Just checking to see what my "signature" looks like.